STEAM CONDENSERS

STEAM CONDENSERS


Thermal efficiency of a closed cycle power developing system using steam as working fluid and
working on Carnot cycle is given by an expression (T1– T2)/T

1. This expression of efficiency shows that the efficiency increases with an increase in temperature T land decrease in temperature T.

The maxi-mum temperature T1 of the steam supplied to a steam prime mover is limited by material considerations.                                                                                                                                            The temperature T2 (temperature at which heat is rejected) can be reduced to the atmospheric tempera-ture if the exhaust of the steam takes place below atmospheric pressure. If the exhaust is at atmospheric pressure, the heat rejection is at 100°C. Low exhaust pressure is necessary to obtain low exhaust temperature.

But the steam cannot be exhausted to the atmosphere if it is expanded in the engine or turbine to a pressure lower than the atmospheric pressure. Under this condition, the steam is exhausted into a vessel known as condenser where the pressure is maintained below the atmosphere by continuously condensing the steam by means of circulating cold water at atmospheric temperature.

A closed vessel in which steam is condensed by abstracting the heat and where the pressure is
maintained below atmospheric pressure is known as a condenser.The efficiency of the steam plant is
considerably increased by the use of a condenser. In large turbine plants, the condensate recovery be-comes very important and this is also made possible by the use of condenser.

The steam condenser is one of the essential components of all modern steam power plants.
Steam condenser are of two types:
1. Surface condenser. 2. Jet condensers


SURFACE CONDENSERS
In surface condensers there is no direct contact between the steam and cooling water and the
condensate can be re-used in the boiler: In such condenser even impure water can be used for cooling
purpose whereas the cooling water must be pure in jet condensers. Although the capital cost and the
space needed is more in surface condensers but it is justified by the saving in running cost and increase
in efficiency of plant achieved by using this condenser. Depending upon the position of condensate
extraction pump, flow of condensate and arrangement of tubes the surface condensers may be classified
as follows:
(i) Down flow type.Fig. 1. shows a sectional view of dawn flow condenser. Steam enters at the
top and flows downward. The water flowing through the tubes in one direction lower half comes out in
the opposite direction in the upper half Fig. 2. shows a longitudinal section of a two pass down-flow
condenser.

Fig.1

Fig. 2

(ii)  Central flow condenser.Fig. 3 shows a central flow condenser. In this condenser the

steam passages are all around the periphery of the shell. Air is pumped away from the centre of the

condenser. The condensate moves radially towards the centre of tube nest. Some of the exhaust steams

while moving towards the centre meets the undercooled condensate and pre-heats it thus reducing undercooling.

(iii)  Evaporation condenser.In this condenser (Fig. 3) steam to be condensed is passed

through a series of tubes and the cooling waterfalls over these tubes in the form of spray. A steam of air

flows over the tubes to increase evaporation of cooling water, which further increases the condensation

of steam.

Fig 3

ADVANTAGES AND DISADVANTAGES OF A SURFACE CONDENSER

The various advantages of a surface condenser are as follows:

1. The condensate can be used as boiler feed water.

2. Cooling water of even poor quality can be used because the cooling water does not come in

direct contact with steam.

3. High vacuum (about 73.5 cm of Hg) can be obtained in the surface condenser. This increases

the thermal efficiency of the plant.

The various disadvantages of' the surface condenser are as follows:

1. The capital cost is more.

2. The maintenance cost and running cost of this condenser is high.

3. It is bulky and requires more space.

REQUIREMENTS OF A MODERN SURFACE CONDENSER

The requirements of ideal surface condenser used for power plants are as follows:

1. The steam entering the condenser should be evenly distributed over the whole cooling sur-face of the condenser vessel with minimum pressure loss.

2. The amount of cooling water being circulated in the condenser should be so regulated that the

temperature of cooling water leaving the condenser is equivalent to saturation temperature of

steam corresponding to steam pressure in the condenser.

This will help in preventing under cooling of condensate.

3. The deposition of dirt on the outer surface of tubes should be prevented.

Passing the cooling water through the tubes and allowing the steam to flow over the tubes achieve

this.

4. There should be no air leakage into the condenser because presence of air destroys the vacuum

in the condenser and thus reduces the work obtained per kg of steam. If there is leakage of air

into the condenser air extraction pump should be used to remove air as rapidly as possible.

JET CONDENSERS

In jet condensers the exhaust steam and cooling water come in direct contact with each other.

The temperature of cooling water and the condensate is same when leaving the condensers.

Elements of the jet condenser are as follows:

1. Nozzles or distributors for the condensing water.

2. Steam inlet.

3. Mixing chambers: They may be (a) parallel flow type (b) counter flow type depending on

whether the steam and water move in the same direction before condensation or whether the

flows are opposite.

4. Hot well. In jet condensers the condensing water is called injection water